The power factor penalty in the Dominican Republic: what it is, what it costs, and how to eliminate it
If your power factor is below 0.90, EDENORTE, EDESUR or EDEESTE charge you a surcharge every month. What causes it, how to find it on your bill, and why it is the fastest saving to capture.
By David Bermúdez · November 20, 2026
Of all the charges on a commercial or industrial electricity bill in the Dominican Republic, the power factor surcharge is unique: it is the only one you can eliminate entirely, with an investment that typically pays back in months. Yet many mid-size and large operations pay it every month without knowing.
What is power factor, in plain words?
Power factor measures how much of the electricity you receive becomes useful work. A value of 1.00 would be perfect; motors, compressors, pumps and air-conditioning equipment — the backbone of any plant or hotel — naturally degrade it, because besides doing work they need to “magnetize”, consuming reactive energy.
Think of the foam on a glass of beer: you pay for the full glass, but only the beer is useful work. The foam is reactive energy — and past a certain limit, the utility bills you for it separately.
When does the surcharge apply, and where does it show on my bill?
The SIE (electricity regulator) sets the threshold at 0.90: if your average power factor for the period falls below it, your utility (EDENORTE, EDESUR or EDEESTE) applies the reactive-energy surcharge. On the bill it appears as “energía reactiva”, “kVarh” or a low-power-factor surcharge line.
The amount depends on how far below 0.90 you are and on the size of your consumption — in industrial operations it can be a significant share of the bill, month after month. The key point: that money buys nothing. No production, no comfort, no operating hours. It is a purely avoidable charge.
Power factor is not corrected by eye: first you measure each circuit’s real load — with CT sensors like this one — then you size the bank.
What causes low power factor?
Inductive loads: electric motors (especially at partial load), refrigeration and air compressors, pumps, HVAC equipment, old lighting ballasts and lightly loaded transformers. If you run a plant, a hotel with chillers, a cold-chain logistics center or an office building with heavy A/C, you have all the ingredients.
A detail that surprises operators: the problem gets worse when load drops — a motor at half load has worse power factor than at full load. That is why the surcharge sometimes rises precisely in low-production months.
How is it eliminated? What is a capacitor bank?
A capacitor bank compensates reactive energy locally: your equipment draws it from the bank instead of the grid, and the power factor the utility measures returns above 0.90. Correctly installed, the surcharge disappears from the next billing cycle.
The key word is correctly. The bank must be sized from real measurements of your load, not estimates: undersized leaves surcharge on the table; oversized can overcompensate and create voltage and resonance problems. Where variable-frequency drives are present, harmonics must be assessed before installing. That is why at Boost we measure first — circuit by circuit — and size afterwards.
How fast does the correction pay for itself?
It depends on the surcharge and the installation, but the industry’s working rule is that a well-sized power factor correction project pays back in months, not years — and after that point the saving is permanent as long as the bank gets basic maintenance. It is the classic “first project”: it funds the next efficiency steps with its own savings.
At Boost we verify it like everything else: surcharge measured before and after, under the IPMVP protocol, so the savings figure stands up in front of your CFO.
Frequently asked questions
How do I know what I am paying in surcharges right now?
Take your latest bill and look for the reactive-energy or power-factor surcharge line. If you cannot identify it, send it to us: the free bill review includes exactly this diagnosis, in writing.
Does installing a capacitor bank require stopping operations?
A typical installation is coordinated with your maintenance team and carried out without stopping production, in an agreed window.
Does this apply to my operation?
We work with commercial and industrial operations spending from roughly US$100,000 a year on electricity — the range where the power factor surcharge alone usually justifies the project. Below that size, correction may still be viable with a local electrician, but our measurement-and-verification model would not be the most efficient route for you.
Apply this to your own bill
Send us your bill and receive the free diagnosis: tariff, billed demand, power factor and errors, in writing.